Welcome to M1911.ORG
The M1911 Pistols Organization Forums Site


John needs your help
Please read this message.


Sponsors Panel
If you intend to buy something from the companies advertising above, or near the bottom of our pages, please use their banners in our sites. Whatever you buy from them, using those banners, gives us a small commission, which helps us keep these sites alive. You still pay the normal price, our commission comes from their profit, so you have nothing to lose, while we have something to gain. Your help is appreciated.
If you want to become a sponsor and see your banner in the above panel, click here to contact us.

Page 5 of 5 FirstFirst 12345
Results 41 to 44 of 44

Thread: Does anyone own one these?

THREAD CLOSED
This is an old thread. You can't post a reply in it. It is left here for historical reasons.Why don't you create a new thread instead?
  1. #41
    Join Date
    29th May 2004
    Location
    Athens, Greece, Earth
    Posts
    28,076
    Posts liked by others
    204
    Blog Entries
    2
    Quote Originally Posted by AFMan
    If I were to spend more than that for a "better" gun today, it would likely be a No Name model from Gun Crafter, especially if I could get one in stainless.
    That, I would get too.
    John Caradimas SV1CEC
    The M1911 Pistols Organization
    http://www.m1911.org
    Last edited by John; 1st November 2011 at 16:37.


  2. #42
    Rio Vista Slim Guest
      
    Quote Originally Posted by AFMan
    If Cabot's "big secret" is holding tight tolerances in machining, that isn't really new to 1911s.
    Actually, it is new.

    When tolerances of .001 of an inch are discussed, the actual tolerance between the rails of the frame, and the corresponding cuts in the slide measure out to .0005 of an inch, on each side. In many instances, that tolerance is closer to .0002!

    Remember, the average human hair is .003 of an inch.

    While I have no doubt that many competent gun manufacturers can work toward the tolerances mentioned, they would be hard pressed to do it consistently. By consistently, I mean gun after gun, time after time, each and every time. This is what the technicians and machine-operators at Penn United Technologies do every day. That expertise is exhibited in the guns which they make, as well as the thousands of other products offered by the company.

    That front sight is a true thing of beauty, and I would NEVER denigrate the superb work done by Joe C.

  3. #43
    Join Date
    21st January 2010
    Location
    Republic of Texas
    Posts
    74
    Posts liked by others
    0
    Steve,

    Thanks for the explanation about Cabot's machining tolerances, but for some reason, I can't reconcile a company dedicated to precision with the way the rear of the frame and slide on your example fail to line up.

    At a price point of $4450, I think Cabot would do well to pay a bit more attention to the external details.
    Old enough to know better.

  4. #44
    Join Date
    2nd June 2004
    Location
    Terra
    Posts
    22,286
    Posts liked by others
    906
    Considering that our review of the Cabot 1911 pistol is now up for your perusal in our e-zine and that we have a discussion thread for that article here http://forum.m1911.org/showthread.php?t=96491 I think this thread has run its course. Please read the review, and then post your comments in the discussion thread created for the purpose. It's going to get confusing if we have two, parallel threads running, so I'm going to close this one.
    Hawkmoon
    On a good day, can hit the broad side of a barn ... from the inside

Page 5 of 5 FirstFirst 12345

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  



Sponsors Panel
If you intend to buy something from Brownells, please use their banners above. Whatever you buy from them, gives us a small commission, which helps us keep these sites alive. You still pay the normal price, our commission comes from their profit, so you have nothing to lose, while we have something to gain. Your help is appreciated.
If you want to become a sponsor and see your banner in the above panel, click here to contact us.

Non-gun-related supporters.
Thank you for visiting our supporters.